Product ID:METALLIC CONDUCTOR-A'NICKEL
MSDS Date:01/11/1990
FSC:5340
NIIN:00N018020
MSDS Number: BLWNW

Emergency Phone: 301-392-3700

Info Phone: 602-431-0077; 302-738-4880

Preparer: MARTIN J HEALY CIH

Cage: 0ADM8

Telephone: 302-368-3700/ 703-527-3887

Cage: 17217

NICKEL

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: >99%

OSHA PEL 1 MG/M3 (METAL)

ACGIH TLV: 1 MG/M3 (METAL)

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:ACUTE/CHRONIC: SPECIALTY FINE WIRE IS
GENERALLY NOT CONSIDERED HAZARDOUS IN FORM SHIPPED. HOWEVER, IF
YOUR PROCESS INVOLVES GRINDING, MELTING, WELDING, CUTTING OR ANY
OTHER PROCESS THAT CAUSES A RELEA SE OF DUST, FUME OR GAS, IN
CONCENTRATIONS GREATER THAN ALLOWABLE EXPOS LIMITS, THE FOLLOWING
EFTS (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NICKEL: CLASS 2 (NTP), CLASS 2B (IARC)
Effects of Overexposure:HLTH HAZ: MAY BE OBSERVED: ACUTE: METALLIC
TASTE, IRRITATION OF EYES, NOSE, THROAT & SKIN, NAUSEA, TIGHTNESS
OF CHEST & FEVER. CHRONIC: SKIN SENSITIZATION, NEUROLOGICAL DAMAGE
& RESPIRATORY DISEASE. I NGEST OF LARGE ENOUGH QUNTITIES TO CAUSE
ADVERSE HEALTH EFFECTS UNLIKELY.
Medical Cond Aggravated by Exposure:SOME WORKERS MAY BE AFFECTED BY
PRE-EXISTING RESPIRATORY OR ALLERGIC CONDITIONS.

First Aid:INHAL: REMOVE TO FRESH AIR & OBTAIN PROMPT MED ATTN. GIVE CPR
IF NEEDED. CONSULT MD. SKIN: WASH AFFECTED AREA THOROUGHLY W/SOAP &
WATER. IF IRRITATION OCCURS, CALL MD. INGEST: INDUCE VOMITING IF
CONSC IOUS & CALL MD. EYE: FLUSH THOROUGHLY W/WATER FOR A MINIMUM
OF 15 MIN, HOLDING LIDS OPEN. CALL MD.

Flash Point:NOT FLAMMABLE
Extinguishing Media:METALIC CONDUCTOR IS NOT FLAMMABLE. USE
EXTINGUISHING MEDIA SUITABLE FOR SURROUNDING FIRE.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED PRESSURE DEMAND SCBA
& FULL PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE.

Spill Release Procedures:SHOVEL SOLID INTO CONTAINER. MINIMIZE DUST.
VACUUMING PREFERRED.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:NONE SPECIFIED BY MANUFACTURER.
Other Precautions:THIS PRODUCT CONTAINS ONE OR MORE CHEMICALS SUBJECT
TO THE REPORTING REQUIREMENTS OF SARA TITLE III, SEC 313; STATE
RIGHT TO KNOW LAWS (MA, NJ, PA); &/OR CALIF PROP 65.

Respiratory Protection:RESPIRATORY PROTECTION IS NOT NORMALLY REQUIRED
UNDER ANTICIPATED CONDITIONS OF USE. IF RESPIRATORS ARE NECESSARY,
USE ONLY NIOSH/MSHA APPROVED RESPIRATORS.
Ventilation:USE LOCAL MECH EXHAUST VENT WHEN PROCESSING MATL. COULD
RELEASE DUSTS, FUMES OR GASES IN CONCS >ALLOWABLE EXPOS LIMITS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
HAZ DECOMP PRODS: THESE CONSTITUENTS MAY INCLUDE OXIDES OF METALS,
CHROMATES, FLUORIDES, CO, CO2, OZONE & NOX.

HCC:N1
Solubility in Water:INSOLUBLE.
Appearance and Odor:METALLIC CONDUCTOR, SERVE WIRE SHIELD, BRAID, FOIL
SHIELD. NO ODOR.

Stability Indicator/Materials to Avoid:YES
ACETYLENE, STRONG ACIDS & BASES & OXIDIZING AGENTS SUCH AS HYDROGEN
PEROXIDE.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:FUMES & GASES FROM WELDING/HIGH TEMP
CUTTING MAY CONTAIN CONSTITUENTS DIFFERENT THAN THOSE LISTED IN
INGRED. (SUPP DATA)

Waste Disposal Methods:DISPOSE OF ACCUMULATED WASTE I/A/W APPLICABLE
FEDERAL, STATE, AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.